CubeMX - STM32 encoder interface

Couple a days ago, I've got struck with connection of encoder to my stm32 board. But,    the answer to the puzzle was quite simple:) So, just watch on screenshots:
Pin configuration:





Timer configuration:



Wiring is quite simple - encoder has 3 outputs. Central connect to GND, others - connect to timer's inputs.

Code is simple too:)
 int main(void)  
 {  
  /* USER CODE BEGIN 1 */  
  /* USER CODE END 1 */  
  /* MCU Configuration----------------------------------------------------------*/  
  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */  
  HAL_Init();  
  /* Configure the system clock */  
  SystemClock_Config();  
  /* Initialize all configured peripherals */  
  MX_GPIO_Init();  
  MX_TIM1_Init();  
  /* USER CODE BEGIN 2 */  
  HAL_TIM_Encoder_Start(&htim1,TIM_CHANNEL_ALL);  
  /* USER CODE END 2 */  
  /* Infinite loop */  
  /* USER CODE BEGIN WHILE */  
  int i = 0;  
  while (1)  
  {  
  /* USER CODE END WHILE */  
  /* USER CODE BEGIN 3 */  
   i = TIM1->CNT;  
  }  
  /* USER CODE END 3 */  
 } 

So, you just need to enable encoder through function HAL_TIM_Encoder_Start.

Comments

  1. CandanJanuary 10, 2016 at 9:34 AM

    Very nice explanation, thanks for the contribution.

    ReplyDelete
  2. UnknownDecember 4, 2016 at 1:08 PM

    Thanks man, saved me some time!

    ReplyDelete
  3. AnonymousDecember 14, 2016 at 11:10 AM

    Thanks..

    ReplyDelete
  4. No LostDecember 20, 2016 at 10:05 PM

    thank you very much, just wondering this for a long time

    ReplyDelete
  5. TomMay 9, 2019 at 12:07 PM

    Thank you.

    ReplyDelete
  6. Stephen DevaneOctober 1, 2019 at 1:20 PM

    Can thuis be used to count motor quadrature pulses?

    ReplyDelete
    Replies
    1. Artyom SinitsinOctober 2, 2019 at 12:39 AM

      This approach can be used for any incremental encoder interface.

      Delete
  7. karlosMarch 23, 2020 at 5:13 AM

    thanks for your fine explanation, I was reading HAL manual, but have not figured how to start the timer with it

    ReplyDelete
  8. UnknownMay 27, 2020 at 3:21 PM

    Thank you for saving me a bunch of time !

    ReplyDelete
  9. UnknownMarch 21, 2022 at 6:08 AM

    but you arent using i in the code?

    ReplyDelete
  10. AnonymousNovember 24, 2024 at 11:05 AM

    Kami memahami bahwa biaya menjadi faktor penting dalam memilih jasa arsitek. Oleh karena itu, kami menyediakan biaya desain rumah yang kompetitif tanpa mengurangi kualitas desain. Kami juga menyediakan informasi mengenai harga jasa arsitek per m2 yang jelas, sehingga Anda dapat merencanakan anggaran dengan lebih baik. Selain itu, bagi Anda yang membutuhkan biaya jasa arsitek untuk renovasi rumah, kami dapat memberikan perkiraan biaya yang transparan dan membantu Anda dalam merencanakan renovasi rumah.

    Bagi Anda yang mencari jasa arsitek murah, kami menawarkan berbagai pilihan layanan yang dapat disesuaikan dengan anggaran Anda. Kami juga menyediakan jasa arsitek rumah murah tanpa mengorbankan kualitas desain yang Anda inginkan. Kami berkomitmen untuk memberikan harga jasa arsitek yang wajar dan sesuai dengan standar industri. Jasa Arsitek Medan

    ReplyDelete

Post a Comment

Popular posts from this blog

u8g2 library usage with STM32 MCU

Image
Several years ago I wrote couple of articles about beautiful library u8glib in context of STM32 microcontrollers. Time moves on and author of this library released newer one, u8g2. u8glib is officially deprecated and not developed anymore. We cannot afford to lose code support for our libraries, time to move to newer library! Differences between these libraries are listed there, also there are a lot of helpful information about u8g2 library. It is not so hard to modify your old u8glib code for newer library. I'll show you how to use this library with Nucleo-F401 board and SSD1306 display, bought on Aliexpress. Display connection is SPI, pins are GND, VCC, SCL(the same as SPI clock), SDA(the same as MOSI), RES and DC. Wiring is: PA5 -> SCL PA7 -> SDA PA9 -> OLED_RES PC7 -> OLED_DC I use CubeMX code generation tool to initialize all the peripheral.  OLED_RES and OLED_DC is just GPIO output. SPI1 initialized with default parameters. u8g2 library has it...
Read more

Use PCM5102 with STM32

Image
Use PCM5102 with STM32 PCM5102 and STM32 Here are my tiny notes about the connection of PCM5102 DAC to STM32F401 Nucleo board. I2S interface requires three wires to work: SCK is officially called as “continuous serial clock (SCK)”, but also you can found “bit clock” name. It is just the same clock as usual in the SPI interface. Word Select clock is used to select, which cannel is active now, 0 for left channel, 1 for right. It also called called “left-right clock (LRCLK)” or “frame sync (FS)”. Serial data - actual data. CubeMX settings Wiring diagram My board has such pins: | 3.3V | 3.3V on Nucleo board | | FLT | Filter select, grounded: select normal latency, grounded | | DMP | De-emphasis control, grounded(OFF) | | SCL | System clock input, in datasheet SCK pin. System clock is internally generated, it should not be wired anywhere | | BCK | Audio data bit clock input. In I2S terminology is equivalent to serial clock(SCK) I've connected i...
Read more

RFFT in CMSIS DSP. Part 1.

Image
RFFT in CMSIS DSP. Part 1. RFFT in STM32 using CMSIS DSP. Part 1. Python warm-up for illustration I always wanted to use MCU for audio processing. And for my purposes, I need Discrete Fourier Transform(DFT), especially its fast version FFT. If you do not know what is this, read Wikipedia first:) FFT has a huge number examples of usage, for my case I want to build wavetable synthesizer. Let’s take some real example. We have an audio signal, which is just a set of amplitudes, which you will take from your ADC. Samples are taken with some sampling frequency Fs. For preliminary illustration, we’ll use Python. import numpy as np import matplotlib . pyplot as plt # Our wave settings N_samples = 32 amplitude = 10 # Here we'll generate our sine wave t = np . arange ( N_samples ) x = amplitude * np . sin ( 2 * np . pi * t / N_samples ) # Plotting fig , ax = plt . subplots ( ) ax . plot ( t , x , 'bo-' ) ax . set_xlabel ( 'N sa...
Read more